GE DVD Recorders + RW Universal Remote Codes


Controlling your GE DVD Recorders + RW is not possible until you have the working codes. So here on this platform, you will get a complete list of the codes that are working properly. You cannot control your GE DVD Recorders Plus RW unless you have the valid codes. You can get a complete list of the codes that are suitable on this platform. You don’t need to bring a different remote for each of your devices. Apart from this, the process you must follow is easy to understand.

Programming these codes doesn’t require any further knowledge; see here for the GE codes for a universal remote.  Now you may pass the time with your preferred GE DVD recorders +RW device.

GE DVD Recorders + RW Universal Remote Codes List

CENTRIOS0951, 1060, 1061
GO-VIDEO0431, 0902, 0901
JVC0900, 1072
LITEON0902, 0898, 0959
MAGNAVOX[0979], [0980]
MEDION0903, 0959
PHILIPS[0979], [0980]
PHILIPS-MAGNAVOX[0979], [0980]
PIONEER0977, 0909, 1084
SONY0987, 0988, 0989
TOSHIBA0973, 0398
YAMAHA0979, 0980

How to Program GE Universal Remote Without Codes

All universal remote control codes are scanned in the remote during the auto-search procedure. To program the control, it scans one code at a time to find the correct remote code that works with your remote. Follow the instructions below:

  • Turn on the smart device you want to use the universal remote to control, such as the TV.
  • To “turn on” a device, press and hold the TV, DVD, CBL, and OK/SEL buttons for 3 seconds. The device is ready to program, according to the LED light.
  • Use the remote to choose the “CH+” and “CH-“ switches.
  • On/off indications are displayed on the remote. Continuously press the “up” or “down” key until the device turns off.
  • Click the “power” key to confirm the code. It should start up. If it does, check a different channel to make sure the remote is programmed properly.

To store the code, press the “device” button now. The device’s LED will flash twice to verify the code that was saved.

How to Program GE Universal Remote With Manual Method

The universal remote may be easily programmed using the keycode, which also helps to identify the make and model of your device.

  • You must “Turn The Device On”.
  • Click “TV” on your “GE universal remote”
  • As soon as the universal remote displays the “Light Flash” (a sign that it is in “Learning mode”), push and hold the “Setup button” for a few seconds.
  • Finally, input the “Keycode” that you have obtained from the Instructions Booklet for programming.
  • Simply “point your remote at the TV” after completing this step, and then “Press and Hold The Power” button.
  • When the screen switches off, you can let go of the “Power Button”.

That’s all there is to it; your TV should now work perfectly with the universal remote control. If not, try repeating the process with a new code from the same section of the reference table.

You can put your universal remote to search mode and look for the right key code if you are unable to find it at that moment. The remote control is forced into search mode by a code in the instructions.

  • “Turn The Device On”.
  • Hold down the “Setup” button for a moment.
  • Enter the “9-9-1” (three-digit) code after which you must continue to hold down the “Power Button” on the remote control while pressing the Channel up button until the device, in this case, your TV, “Turns Off.”

Finding your key code may take some more time using the above-mentioned method, but it is essential. Your remote should function properly for all in-room functions once you have completed the above steps.


Now that the article is over, I hope you can effectively operate your GE CABLE Set-top Box devices using the universal remote. And I have no doubt that you will be able to achieve anything.

All of this has to do with the GE DVD Recorders + RW Universal Remote Codes, and now is the time to watch TV shows and go to the movies without getting a headache. You can now easily program your remote controls to control your different devices.

Read Also: gpx dvd player universal remote codes


How can I find the GE universal remote code for my device?

Your device’s GE universal remote code is often listed in the manual that came with your remote, in the handbook for your device, or online by searching for the model number and “GE universal remote code.” Additionally, certain GE universal remote controls have a code search feature that makes it simpler to find the right code

Can I control multiple devices with my GE universal remote?

Yes, your GE universal remote can operate multiple devices. Just repeat the setup procedures for each device you want to program.


Please enter your comment!
Please enter your name here