Dynex DVD Universal Remote Codes List


Do you know how your home entertainment system’s various components can all be managed by a single remote control? You can operate multiple devices with a Dynex DVD remote if you have one. Programming the remote is easy and only needs a few steps, along with the essential and special Dynex DVD universal remote codes. The complete list of Dynex DVD player remote codes for the device you select is available along with programming instructions.

Dynex DVD Universal Remote Codes List

Almost all of the universal remote codes for Dynex DVD players and other video/audio devices will be included on this page. When programming, the suitable universal remote code will be used for the Dynex DVD player and the desired device. The list of Dynex DVD player remote codes is provided below:

Dynex DVD Player Universal Remote 5 Digit Codes

  • 10463
  • 22596 
  • 32596 
  • 52522
  • 52345
  • 54525

Dynex DVD Player Universal Remote 4 Digit Codes

  • 2596 
  • 4235
  • 2455
  • 2255 
  • 6126
  • 1710

Read Also: Symphonic DVD Player Universal Remote Codes

How to Program Dynex DVD Universal Remote

When you choose to sync the Dynex DVD universal remote with other home entertainment systems, you will experience a variety of benefits. Please remember that when setting up your preferred device Dynex DVD player codes for universal remote are important.

You may program the Dynex DVD remote by following the steps below:

How to Program Dynex DVD Universal Remote Without Codes

All universal remote control codes are scanned in the remote during the auto-search procedure. To program the control, it scans one code at a time to find the right remote code that works with your remote. Follow the instructions below:

  • Turn on the smart device you want to use the universal remote to control, such as the TV.
  • To “turn on” a device, press and hold the TV, DVD, CBL, and OK/SEL buttons for 3 seconds. The device is ready to program, according to the LED light.
  • Use the remote to choose the “CH+” and “CH-“ switches.
  • On/off indications are displayed on the remote. Continuously press the “up” or “down” key until the device turns off.
  • Click the “power” key to confirm the code. It should start up. If it does, check a different channel to ensure the remote is programmed properly.
  • To store the code, press the “device” button now. The device’s LED will flash twice to verify the code that was saved.

How to Program Dynex DVD Universal Remote With Manual Method

The universal remote may be readily programmed using the keycode, which also identifies your device’s make and model.

  • You must first “Turn The Device On.”
  • On your “Dynex DVD universal remote,” choose “TV.”
  • In order to put the universal remote in “learning mode,” press and hold the “Setup button” until it flashes a light.
  • At last, key in the “Keycode” you collected from the programming manual (Instructions Booklet)
  • Just “point your remote at the TV” after completing this step, and then “Press and Hold The Power” button.
  • When the screen switches, you can release the “Power Button.”

That’s all there is to it; your TV should now operate perfectly with the universal remote control. If not, try repeating the process with a new code from the same section of the reference table.

You can put your universal remote to search mode and look for the right key code if you are unable to find it at that moment. The remote control is forced into search mode by a code in the instructions.

  • “Turn The Device On” first.
  • Hold down the “Setup” button for a moment.
  • Enter the “9-9-1” (three-digit) code after which you must continue to hold down the “Power Button” on the remote control while pressing the Channel up button until the device, in this case, your TV, “Turns Off.”

Finding your key code may take a little more time using the above method, but it is very important. Once you’ve completed the above steps, your remote should be working for all the functions.


Have you been able to program the Dynex DVD remote control? If you agree with this post, kindly share your thoughts with us. You can send us information about the correct code you used and the device type it matches. Please feel free to comment below with your ideas.


What is the Dynex code for RCA universal remote?

Replacement for RCA 3-Device Universal Remote Control Palm Sized – Works with Dynex TV – Remote CodeĀ 1463, 2049, 2184

How do you code a universal remote?

Make sure the device you want to pair is powered on and that the remote has working batteries in it.
Press and hold the appropriate device button. …
Enter the correct code for your device while continuing to hold the device button. …
Once the power button lights up again, you can release the device button.


Please enter your comment!
Please enter your name here